Top 10 common forklift crashes ， forklift operation need to focus on these issues ！.

Don't underestimate the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are numerous accidents involving forklifts.

Instance 1: The forklift freight obstructed the driver's sight, and the person in front can not be found, causing a moving mishap.
Case 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees used their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the allowed width of the path and holds on the roadside shelf, which practically triggers an mishap.
Instance 4: Forklift is speeding up and surrender throughout a turn.
Instance 5: The forklift chauffeur did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the employees illegally, the forklift vehicle driver does not use the safety belt, the forklift lifter falls and the driver is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a seat belt and dropped from the automobile when it surrendered and was squashed.
Forklift procedure must pay attention to these matters ：.

Begin.
1. Before starting, observe the environments, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a lots, the driver needs to first verify that the load is secure and reliable.
4. The begin should be sluggish and consistent.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the pole must be slanted in reverse. .
2. Do not raise the fork expensive when driving. When entering and leaving the work site or while driving, be careful that there will certainly be no challenges overhead. When the tons is traveling, the fork needs to not be elevated too expensive, which will certainly influence the stability of the forklift. .
3. After unloading, the fork must be reduced to the normal driving setting before driving. .
4. When transforming, if there are pedestrians or vehicles close by, the driving signal needs to be released initially. High-speed doglegs are forbidden. High-speed sharp turns will trigger the vehicle to lose side stability and tip over. .
5. When the forklift is downhill, it is strictly restricted to turn off the flame and slide, and it is forbidden to brake all of a sudden while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and should maintain a particular safety distance from the vehicle ahead. .
7. When the forklift is running, the load should be in the lowest setting that does not impede the driving, and the gantry ought to be appropriately slanted back. The tons will not be increased except when piling or loading. .
8. The height of the load have to not obstruct the driver's sight. In unique circumstances, when the product influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it has to drive securely at a reduced rate when getting in the production workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold things and play a stabilizing Electric Forklift Truck for Warehouse function. .
12. If issues are discovered, they will be fixed and reported in a prompt way, and they will certainly never ever run with health problems or hide them.

packing and dumping.
1. When fork-loading items, the distance between the two forks ought to be adjusted as required to make the lots Stand-on Electric Pallet Stacker of both forks balanced and not manipulated, and one side of the thing need to be against the rack. .
2. It is prohibited to collaborate with a single fork or utilize a fork top or draw. In unique scenarios, security indication need to be set up to remind surrounding pedestrians. .
3. In the process of packing and discharging products, the forklift must be braked with the brake. .
4. The rate of the automobile need to be sluggish and consistent. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork should be as deep as feasible under the tons, and it must be kept in mind that the fork tip need to not touch various other products or things. The tons needs to be supported with minimal back tilt of the gantry so that the load does not glide backwards. The mast can be slanted forward somewhat when the lots is lowered to enable easy placement of the load and extraction of the forks. .
6. It is prohibited to fork goods at broadband and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to prevent the collapse of the goods and harm people. .
8. Overwhelming is banned, and it is banned to make use of forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not allowed to use the brake inertia to slide, place, round or roll items. .
10. It is not enabled to use forks to select, transform pallet unload.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you need to discharge the goods or lower the fork framework.
2. Draw the emergency brake take care of to dead or dispirit the parking brake button.
3. The engine is shut off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water ought to be added.
2. Examine the safety and security performance of beginning, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, examine whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leak must likewise be checked and the seals must be changed in time.

Forklift Safety Operation Specifications.
1. You must inspect prior to leaving the cars and truck;.
2. When you come across someone in front of you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to stop the propensity of " cost-free switching";.
6. Running up and down the slope should be slow and consistent, and no switching on the incline is permitted.
7. Do not drive across the gradient. When the slope is above 10%, the car should be driven backwards when going downhill;.
8. When the forklift employees carry the goods and move forward, if they come across large or hefty items and go to the vehicle driver's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Solitary fork procedure is not allowed.
2. It is not permitted to raise the goods for cross country driving.
3. It is not permitted to get the goods by handing over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not permitted to use braking force to expatriation round or easy-to-roll things.
7. It is not permitted to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not permitted under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Sections with a longitudinal incline higher than 5%.
3. When there is an challenge on one side of the road, the contrary side of the area with the very same size as the barrier ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844